| Thread | Last Post | Replies |
|
| rear seat removal in '95 Mercury Villager | 06 Jul 2006 17:51 GMT | 1 |
I'm looking at buying a '95 Mercury Villager, but then I noticed that the rear seat does not remove completely? Is that true? There's no way to take it out? I read that you can take out the middle seat and then slide the rear seat forward, but how much cargo room does that give you
|
| Check Thermostat Part # | 06 Jul 2006 03:41 GMT | 1 |
Long story short. I have a 93 Nissa PU 2.4L Auto. Water Pump leaked, replaced water pump, thermostat, hoses, belts, back-flushed,etc, After starting my pu, 5 minutes later...running hot!!!. Checked everything I could check.
|
| 2002 Nissan Altima Back Windows | 06 Jul 2006 00:31 GMT | 3 |
Can anyone confirm (or deny) that a 2002 Altima's back windows only go down about 3/4 of the way? We had screens on the windows for a while to keep the sun out of the faces of our twin babies, and now that they have grown a little, we took the screens off and noticed that the
|
| Air Con (Leak) ? | 06 Jul 2006 00:14 GMT | 9 |
Using Air Conditioning for an hour to day and then parking in the drive, I found evidence of an oil (water )leak. A reasonable new Almeria . Using Air conditioning does this cause a leakage , or should I look
|
| P1145 fuel air metering | 06 Jul 2006 00:04 GMT | 3 |
I have a 2001 QX4 and I got the service engine light.I took it to a friends shop and scanned my car with his actron auto OBDII scanner and it gave that code.He ERASED but as I started the car the light came back.What is the fuel air metering?What does it look like?How much would it ...
|
| Clutch Repair | 05 Jul 2006 15:33 GMT | 5 |
i have nissan sentra 1998 manual 5 spd. yesteraday when i was going at the interstate it just came to standstill. The problem was clutch. even after full release and at low gear it was not transmitting power. I have to get it towed away. I think it is a clutch repair. Can anybody
|
| Sentra strating problem | 05 Jul 2006 12:34 GMT | 2 |
I have a 2004 Nissan Sentra.It starts fine in the morning or after its sitting several hours.But if you park it for 30 minutes after driving it a little while,it is hard to start.It always starts ,but it aggravates my wife .She's always afraid of getting stranded.
|
| 07 Altima | 05 Jul 2006 03:36 GMT | 2 |
Take a look http://www.edmunds.com/insideline/do/FVDP/Photos/styleId=100478581
|
| Oh no, another A/C thread! | 04 Jul 2006 02:14 GMT | 2 |
Simple question for you, I have a 99 Altima and had it into the dealer last year or the year before to have the A/C looked at as it seemed to be not cooling as well as it used to. They found it was about 1 lb low on refrigerant, so they topped it up and put some u/v dye in to ...
|
| pls help me decode VIN for 97 pathfinder | 04 Jul 2006 00:01 GMT | 2 |
I just purchased a 1997 pathfinder. My VIN number is: JN8AR05Y9VW168320 Can someone with a service manual please help me decode the various elements of this VIN number?
|
| 2.4L Squeal on Startup --- Belts or Pulleys/Waterpump? | 03 Jul 2006 22:55 GMT | 3 |
Got a 2.4L Nissan Frontier that squeals like a pig on startup. Turning off the air conditioner helps sometimes, sometimes not. I've heard it's belts, A/C clutch, pulleys, or even the water pump. Is there any consensus out there?
|
| fuel 03-05 Z car and G35 coupe | 02 Jul 2006 17:22 GMT | 7 |
fuel 03-05 Z car and G35 coupe Does this 3.5 engine _require_ premium fuel or is it just recommended for max performance?
|
| climate control swap | 02 Jul 2006 13:12 GMT | 1 |
our 01 pathifnder came with the standard climate control setup, three knobs and some buttons. I noticed in new models or maybe even the same year with a high package the pathfinders have an automatic climate control unit. Does anybody know if this can be interchanged easily or
|
| brake job and rotor resurfacing | 01 Jul 2006 04:56 GMT | 9 |
I have a 2001 Nissan Pathfinder and recently I had the brake pads replaced. The technician at MIDAS called me to say I need to get the rotors resurfaced by the machine. He talked me into getting it done. Is that absolutely necessary to get the rotor resurfaced after installing
|