| Thread | Last Post | Replies |
|
| Weight different between XU alloy & iron blocks? | 27 Apr 2004 19:36 GMT | 2 |
Anyone know how much heavier the iron XU blocks are compared to the alloy ones? It seems like most/all 1998cc XU engines are iron blocks - such as the Citroen XM's 2 litre turbo engine, or the 2 litre 16v engine fitted to later 405's. Just wondering what I could expect to happen if ...
|
| Air Conditioning on R Reg 306 dt | 27 Apr 2004 16:07 GMT | 4 |
Has anyone encountered any problems with the air con on 306's. I had mine refilled last year with coolant and it worked for a while, but then i had a leak. Apparently there are two pipes which can go. High pressure or Low
|
| Peugeot Diesel Alternator.? | 27 Apr 2004 13:24 GMT | 3 |
Does anyone know if the Rover 418 Turbo Diesel(94), which uses a Peugeot engine, also uses a Peugeot alternator? I'm looking for a replacement from salvage but would like to know from which other models I can get one from. Alternatively, if it is a Rover one, which
|
| Auto electrician reguired | 27 Apr 2004 08:25 GMT | 1 |
I have a Peugeot 406 LX 2.0 ltr estate 1997 model. I have lost the readings on the petrol gauge, rev counter and speedo these don't do anything when I start the car or drive it. I have a feeling that these instruments are on the same circuit that's why I feel
|
| any problems with current 307 1.4 hdi s?? | 26 Apr 2004 22:53 GMT | 4 |
I'm about to by a peugeot 307 hdi or xs. I've been reading some problems here about the BSI of 307s and a milage -odometer- problem. How can i be sure the 307 i will buy is free of such problems?
|
| 306 XSi Auto transmission change thumps !!!!! | 25 Apr 2004 19:13 GMT | 1 |
We have owned a '99 306XSi since new and have had a consistent auto gear change "thump" when the 306 starts to accelerate from a strationary position. Peugeot help has been to acknowledge the "problem" and have replaced the
|
| oil leak 306 | 25 Apr 2004 17:05 GMT | 1 |
i have discovered an oil leak on my 306 xsi. it smells like gear oil and is clean so i assume its leaking from the gear box . has anybody had same problem?
|
| HELP peugeot 406 1996 | 25 Apr 2004 11:33 GMT | 1 |
hi need some help with my 406 my speedo comes on when the car is cold in the mornings but goes out after it warms up ? { mabye 5 to ten mins } any ideas?? thanks
|
| 406 HDI timing belt change | 24 Apr 2004 21:46 GMT | 3 |
I am planning to have my timing belt replaced at 66000 miles - should I be looking to replace anything else at the same time such as tensioners, idlers etc? Or is just changing the belt OK?
|
| 106 Cat replaced, now dodgy gear changes | 24 Apr 2004 11:19 GMT | 5 |
106 XN Petrol R Reg Driving up to Birmingham and the exhaust starts roaring. Managed to get it fixed (new catalytic converter), but since then I have had gearbox issues. At 37mph in 4th, there is a loud metal-on-metal shaking noise
|
| 306 Diesel fuel econ | 24 Apr 2004 10:24 GMT | 8 |
I have a diesel 306 - its done 127:000miles I'm having problems working out whether or not I'm getting good miles per gallon. I put ?10 worth of diesel in at a time until the light comes on (approx 12 litres ) and I am getting about 90 miles from this. Is this good / bad? If
|
| 205 1.6 GTI + unleaded | 24 Apr 2004 00:54 GMT | 7 |
I normally use LRP in mt Peugeot 205 1.6 GTI (1989: XU5JA) This petrol is getting harder to obtain. Can I run on unleaded (say 95 octane) without modification. If not what is the best course of action. I tend not to drive on motorways or tow.
|
| Live wire in 405 | 23 Apr 2004 23:07 GMT | 1 |
I have a 1995 405 2L estate and I wish to connect a cigarette charger in the boot in order to recharge my computer. Does any one have any idea of live pick off wire I can utilise?
|
| wind deflectors for a 406! | 23 Apr 2004 22:43 GMT | 1 |
Hi folks, as you may have guessed; I'm still looking for a pair of these, anybody got any to sell, or know of anyone!?? regards, Mark.
|
| removing a radio from a 306 | 23 Apr 2004 22:37 GMT | 2 |
hi can some one tell me how to remove a radio from a 306 just got the car and want to change for a better one but dont know how its fixed i dont have a manuel any help please
|