| Thread | Last Post | Replies |
|
| 406 rear seat removal | 14 Jul 2005 12:01 GMT | 2 |
I have been attempting to remove the rear seat to access the fuel pump, according to the Haynes manual it is simply a matter of undoing two pins at the front of the seat, pulling it forward, lifting and then removing, I have heaved and pulled to no effect, am I doing some thing ...
|
| Peugeot J9 | 14 Jul 2005 11:12 GMT | 2 |
does anyone know if there is some sort of workshop manual for the peugeot J9 van?? thanks stefan
|
| PUG 406 AirCon Problem | 14 Jul 2005 10:13 GMT | 6 |
Got my Pug 406 TDI (1.9) checked as far as aircon gas goes today. I thought it was low as the compressor pump did not seem to be kicking in when I pressed the aircon button on the dash (bulb on button is OK). Gas pressure was perfect when checked.
|
| Juddering | 13 Jul 2005 23:36 GMT | 4 |
Just bought a 306 D turbo `95. i recently changed 5 spoke spiral wheels over to some XSI wheels on jack + axel stands under chassis rail, ever since i have done this, i have been getting major juddering from what i believe to be middle/rear of car under quite firm braking,
|
| Identify the car part... | 13 Jul 2005 22:46 GMT | 6 |
Im useless with cars (well my driving is OK :-)). However, can someone please tell me what this is www.keybm.com/car TIA Oli
|
| Where are the spark plugs in Peugeot 307 1.4 ??? | 13 Jul 2005 22:40 GMT | 2 |
I have just bought 2002 1.4i 8 valve Peugeot 307. Where are located the spark plugs? I am completely confused. Dont't say that it is under the cap of the head. Please give me your advice.
|
| 807 Wipers | 13 Jul 2005 22:30 GMT | 2 |
Does anyone else have a problem with their windscreen wipers (front and rear) activating on their own? As far as I know I don't have any kind of automatic wet sensors to worry about 2.0 GLX Diesel 52 reg.
|
| Peugeot 405 1.4GL of 1993 air conditioner problem | 13 Jul 2005 21:08 GMT | 1 |
I have a problem with air conditioner in my Peugeot 405 1.4GL of 1993 which has installed a DIAVIA air conditioning system and a Sanden compressor. The problem is that the electromagnete of compressor has gone in short
|
| non starting 406 hdi | 13 Jul 2005 18:43 GMT | 4 |
2000 406 hdi car wouldnt startbut after turning engine over 4 about 30 seconds would start.this went on 4 about a week,now car wont start at all. had car diagnosed at local garage and they said the high presure pump was at fault, so had that changed car now starts up straight away
|
| 406 blower motor - where to get replacement crimp pins/connector shell | 13 Jul 2005 13:31 GMT | 4 |
The dodgy connector on the blower fan of my 406 is driving me mad....I've been cleaning up the pins and pushing it back in for the last 6 months but it is finally beyond further repair. The shell is badly burnt so I thought I would chop it off and replace it. Trouble is, I cannot ...
|
| peugeot 106 radio problem | 13 Jul 2005 09:56 GMT | 2 |
I have a standard radio/tape player in my peugeot 106 car. When i turn volume up you can only hear it slightly. On the display screen it comes up with 122 or somenumber. I tried putting in a tape and still with full volume you can only just hear it. How do i reset the radio
|
| Advice on buying a 406 | 13 Jul 2005 09:15 GMT | 9 |
I'm going to look at a 406 GLX - T-reg facelift. It's an HDi car. Are there anything I should look out for other than the usual "used car" type of things? Cheers,
|
| Peugeot 406 HDI Y Reg | 13 Jul 2005 01:36 GMT | 3 |
Anyone know what it should cost for a new cam belt to be fitted?
|
| 406 HDI starting problem (1999) | 12 Jul 2005 02:36 GMT | 2 |
I seem to have a problem with my 406 diesel starting A few weeks ago the car spun over for about ten seconds didn't start I left it for a few seconds and then tried again it started ok I put this down to low fuel as my gauge sometimes drops from 1/3 to
|
| 406 hdi which wires are for the scavanger pump | 12 Jul 2005 02:36 GMT | 2 |
I've been told to check the scavanger pump under the backseat of my 1999 406 hdi to make sure that it's pumping fuel to the injectors Can anyone tell me which of the four wires! are the correct 2 wires for the 12 volt supply to the pump.
|