Is it possible to bleed the slave cylinder with a power pressure bleed pot?
I have bled it before manually with an assistant.  The power bleeder works
great for brakes, I just did not know if you needed to push on the clutch
pedal to get the fluid through to the clutch.

I need to replace the rear speakers in my '87 944S.
I'm told that step one is removing the rear side windows.
Any hints on how to do that without breaking the window?
From the inside or the outside?

I've been offered what purports a 1988 944 Turbo S. It isn't pink and
doesn't have psychedelic upholstery. How can I tell if it is actually
an "S" and not a run-of-the-mill turbo? Thanks in advance!

my daughters 944S has an intermittant dead spot on acceleration - if it were
a carburetted car, I'd figure it was a throttle pump not working - you press
on the gas and there is a loss of power, then after a bit it catches and
pulls normally.  Can you think of anything except the ...

hello all.
i have just been on a 700miles trip in my 944 1982. and i have picked up a
problem during the trip. there is a buzzing in the car (rear) whent he car
warms up, well it seems. cause when i first start the car there is no

Bought a new ignition for the 83 944.  Is it difficult to rekey to
original key?  Thanks Nel:)

I'm having a problem with my 1985 (Early) 944. Yesterday, I noticed
that when I turn left, there's a strange thumping noise coming from
either the front or rear left wheel. I also hear this sound when I go
over a bump or uneven road. The sound does *not* exist at all when I

My 1990 944S2 has been perfect for my two years of ownership.  It has 140k
miles and runs strong every day.  I started it last week and it
immediately stalled.  Started fine again, coughed, then stalled.  If i'm
heavy on the gas, I can keep it running for a while.  Then it will ...

My '83 944 starts, idles, and seems to run fine with the exception of one
problem.  Whenever I get her up past around 4k rpm she sputters.  If I ease her
back down under this threshold she runs fine again.  Since I have a 5 speed it
is pretty easy to avoid this higher rpm range ...

  I'm noticed several places selling rebuild kits for front lower ball-
joints on late model 944s. (the ones that are only generally available with
a $500 lower control arm attached)
  Has anyone purchased and used one of these kits ?

I picked up this car recently it has a hole in the oil pan it still runs
but no oil any one have a eng available in phoenix or close by ? and is
there any special things you need to replace eng. I am new to this type of
car so all help will be great Thanks!

Someone mentioned in one of my other posts that I could reference an online
service manual for my '83 944.  I tried seaching for it without any luck.  Can
anyone supply me with the link???
Cheers!

Asking a question for a friend who's son has a '84 944 that broke the
timing belt. Obviously some of the valve stems were bent as a result,
but he would like to know if the pistons were machined with valve
clearance indentations or were all 4 pistons "indented identically" as

I have a 1988 944 and no spark comes out the coil.  I checked the power
coil to the coil and there is power but nothing comes out.  The DME relay
is new and therefore, power the fuel pump does work.  I wounder if the
reference sensors could be the problem.  At any rate, I took them ...

The bolt that holds my rotor bracket came loose and i got some pretty bad
noise from the distibutor area before i towed the car home.  Once home I
tightened the bolt for the bracket, reinstalled the rotor, cap etc. Car
starts now and the noise is gone but it has a bad miss,rough ...