Anyone know the dupont code for '57 torquoise?
Chip

You know those dume wire wrapped wires that are use to open trunks,
pull on the OD controls, amd a bunxh of other tasksl? I have one that
is rust free, but stiff. I have tried thd Kroil oil, any suggestions
on what to soak the wire in to free it it up.

I was traveling some back roads today, just easing along in mt work related
activities, and stopped at a "yard Sale".
Came away with a 1953 copy of a motors manual, a 1963 copy and a copy for
1966.

Just got back from Atlantic City to find my wife VW broke down with a
coolant leak. I got the thing home to find it was leaking from the water
inlet where the upper radiator hose hooks up. Turns out the damn thing
was cracked since it was made of PLASTIC !

http://cgi.ebay.com/ebaymotors/1955-Packard-Patrician-Studebaker-GARAGE-KEPT-Vin
tage_W0QQitemZ4577457931QQcategoryZ6389QQrdZ1QQcmdZViewItem
How 'bout them 352 liters?
Paul Johnson

  Just bought a new Studebaker rod and I'm bringing it to Md. just to
torment N8. <g> Comments on what I should do with the car in the way of
improvements ? i.e. keep the Moon disks, or go with mags ? I'm not going
to paint the car, or go nuts, but want to play with it for a bit ...

The '64 Champ truck has only one speed on both settings when the switch
is pulled out.  Should I start with the switch or the wiper motor?
Also, there are no dash lights.  Any suggestions are appreciated.

The bad -a.s 56 Transtar is making her last run of the season home to New
Brunswick.Ive been driving her all week and its been a ball but Ive got to
many of them sitting around and winters coming.
Yesterday a rumour started that gas prices were going way up again and

For the few of you who haven't seen any of Dr. Cade's Studes, here are
a few pics. Danny T.; who works for them; sent me these.
http://community.webshots.com/album/452672271eEupHY And this is just
ONE building...

Obviously not a big concern to these guys.

Besides the fact they can't spell. The engine doesn't resemble a 289 at all.

Who all is comming for the Denton Zone meet this weekend and the
Goodguys show next weekend? Due to work I cannot make the actual show
at the zone meet but should be around Friday evening and Saturday
evening. Ill be at Goodguys all weekend and should have one or two of

but with the reserve met at just over $6,000, this Clipper Wagon  would
seem to be worth the money:
http://cgi.ebay.com/ebaymotors/1957-Packard-Clipper-Wagon-RARE_W0QQitemZ45762697
88QQcategoryZ6389QQrdZ1QQcmdZViewItem

Last night I went to bid on an item and got a message that the seller
has certain requirements to accept bids, in this case you had to have a
Paypal account to just place a bid (although the seller accepted other
forms of payment).  Apparently this is a new option for sellers!  I ...

Just saw this on the Top gear TV show. 1000 lbs, 350 HP, 0-60 in the
mids 2.9 seconds. N8 will get wood <g>
Watch the video here:
http://www.arielmotor.co.uk/04/frames.htm  (second one down the page

Well, after the advice from this group, I decided to go ahead and try
to remove the pan.  I have the steering disassembled, and the two LH
exhaust manifold nuts off (OK, one broke).  The manual says to remove
the crossover pipe from the RH pipe.  The muffler clamp came off