Yesterday I was looking at some Studes a guy had sitting around and
mentioned I was looking for a 245.We opened the hood on a Stude school bus
and there sat one.Grabbed the belt and fan and it still turned over even
after sitting for about 20 years.Engine for my CE has been ...

This 58 Hardtop is doing well.
http://cgi.ebay.com/ebaymotors/Studebaker-studebaker-commander-1958-studebaker-c
ommander-2dr-ht-V8_W0QQcmdZViewItemQQcategoryZ6466QQitemZ4631224563QQrdZ1

is at $20K within 24 hours of posting!
WOW!
Might set a record?
http://cgi.ebay.com/ebaymotors/1958-Studebaker-Supercharged-Golden-Hawk-LOW-MILE
S_W0QQitemZ4633158221QQcategoryZ6466QQrdZ1QQcmdZViewItem

I got a call the other night from a fellow in Florida who is looking for a real nice used or NOS passenger door for a 1959 Lark hardtop. According to the parts book 1959 thru 1962 hardtop and convertible doors will fit. If you have such a critter email me off the NG and I'll give ...

This car belongs to member of our chapter. It is a beautiful
automobile.  It was driven to Tri-State in Asheville a couple of years
ago, some of  you may have seen it then. Runs like a top and has been
treated with the utmost care.

Is there a "how to" page on the net that explains how to change a shift
tube in a 55 coupe three speed?
There is nothing in the shop manual that I can find, the operation time
guides do not list the operation.

Cute ad. A real testimony to your ambitions if you can get this looking
like the sample "done" photos in 30 days, as the seller suggests. (Step
right up, all you retirees...)
http://cgi.ebay ...

I have a set of F**d LTD "turbine" alloy wheels that I would like to
use on my 64 Wagonaire..
Has anyone used these type wheels on a Stude?
I have a new set of 205/75/r15 tires that I'd like to use with these

To see what CEOs of hundreds of companies are making and their retirement
benefits, check the website below.  Hint- the average CEO makes 431x what
the workers make.  Put your salary and benefits in the program and see how
long you would have to work to equal your boss's annual ...

Anyone familiar with this company? Nice wheels, but real expensive.
Boy, they would look good on my '57 Packard wagon though.
http://cgi.ebay.com/ebaymotors/PACKARD-WIRE-WHEELS-AMERICAN-HAND-MADE-ALL-YEARS_
W0QQitemZ8054080042QQcategoryZ43955QQrdZ1QQcmdZViewItem
Chip

I need advice on how to best do this. I drilled new 3/8" holes, but the 3/8" dowel
doesn't fit tightly. What size should I drill and what size dowel should I use?
Chip

I would like to convert my '64 Cruiser to 3-point front seat belts.  Has
anyone done this?  Any suggestions as to the source of the belts, or
methods of anchoring the bracket on the B-pillar?
Jim Bradley

  Just got the cheap ebay Avanti in, so far mostly good news. Hog
troughs are fine, body is great, but some bad news for N8. There is a
extra bracket on the side of the engine that does not belong on a R1.<g>
http://www.stude.com/cheap/

...don't know if it will work or not.
Was the tip to use a 60's Jeep shift quadrant to use a Powershift in a
column shift car?
Can you do this with an early (pre-57) steering column, or only 57-up?