| Thread | Last Post | Replies |
|
| Citreon Xsara HDI starter | 10 Jan 2008 22:46 GMT | 2 |
I've got an X reg Xsasa Diesel HDi 90BHP which needs a starter. Since its cold & dark outside (!), would appreciate any tips for changing this. i.e what access is like, how do you get to it, need to remove other bits
|
| Y reg Shogun Classic Diesel starting problem | 10 Jan 2008 20:01 GMT | 13 |
Wifes car would not start the other day. Took booster box, started first time {her batt not flat though] Did a 30mile round trip and blasted it. Drove like a dream all 30m. Following morning, same prob again. No luck with booster box. Mech
|
| Spraying this time of year | 10 Jan 2008 17:34 GMT | 3 |
Im thinking of spraying my car in good old fashioned cellulose, this would be inside a barn to protect it from the elements, but humidity is high this time of year (my humidity gauge is showing 70%-80% ) Does this matter?? as dehumidifying a barn is not an option should I wait ...
|
| Plastic repairs | 10 Jan 2008 17:34 GMT | 7 |
I've got a couple of bits for my MK2 Golf that could do with fixing - an arch spat with a crack in it near the bottom (£46 plus the dreaded!?!), and a couple of sill covers with bits and bobs of broken fixings and the like (they're one of these lovely setups with loads of clips).
|
| Flashing glow plug warning light - Kia Sedona | 10 Jan 2008 10:43 GMT | 3 |
Just started as I neared home today. I'd just driven 65 miles and it was fine but now the lights flashing. Any ideas? Read somewhere that it might be the glow plug heater wire? I'm just
|
| Trailer reversing brake problem ??? | 10 Jan 2008 10:25 GMT | 23 |
My 4 wheel ifor williams trailer drives perfectly OK forwards, and when fully loaded. Seems to be OK when reversing with no load. But as soon as I get some weight in the trailer and try to reverse the
|
| New Focus arriving, old focus price reduction? | 10 Jan 2008 09:02 GMT | 14 |
Saw a review of the new Focus in a sunday rag. As most peeps will want the new one rather than the old one, is it likely that I (who am quite satisfied with the old one) can go to my local friendly Ford dealer and get a new / quite new example of the
|
| 2001 Focus 1.6 Zetec-S engine HT Leads | 09 Jan 2008 21:28 GMT | 12 |
I'm going to replace the HT leads soon on my Focus. Is it wise to stick with genuine Ford or are the Pumaspeed Blues a good alternative? http://www.pumaspeed.co.uk/showdetails.php?id=471 Thanks,
|
| Uneven brake wear | 09 Jan 2008 14:50 GMT | 6 |
A few weeks ago the front brakes started rumbling under braking. I got the front offside wheel off but both pads still had 5mm left. I then took it for it's MoT and it nearly failed on worn brake pads so I bought some and fitted them when I got home. The nearside pads where only ...
|
| Steering problem! Please help! | 09 Jan 2008 13:30 GMT | 11 |
Just wondering if anyone can help me with this? I just bought a year old Vauxhall Astra SRi (15k miles) and have a bit of an issue with the steering. Basically the steering wheel seems to 'wobble' around a lot whenever I run over a small dip/pot hole or even with slight cambers
|
| Airbag light - mot fail? | 09 Jan 2008 11:35 GMT | 11 |
My airbag light is on and the car's MOT is due in 3 weeks. Is it a fail?
|
| bit OT car ins | 09 Jan 2008 10:02 GMT | 16 |
I mentioned a few weeks back, i was hoping to get a German camper...well if all goes to plan i get it next week. Spoke to DVLA, said i can keep it here for a here, as long as i register it in my name, no probs...
|
| Clio immobiliser | 09 Jan 2008 10:01 GMT | 5 |
My son bought a Renault Clio 1.2 some weeks back, assuming he would pass his test first time. He didn't, nor the second, and the Clio sits there looking unloved. I try to give it a short run every week or so, but I'm a bit confused about the immobiliser system. We can unlock the car ...
|
| Unever tyre wear | 09 Jan 2008 08:01 GMT | 1 |
Is it possible to narrow down the cause of this? O/S front tyre, nearly bald on inner 20% of tread, 6-8mm over rest of tread. The N/S front tyre wear is even. Sierra 1.8LX 1990
|
| Disassembling distributor - Help | 08 Jan 2008 20:40 GMT | 11 |
I need some help to disassemble the distributor (I will fabricate a bracket out of it). I removed rotor arm, mechanical advance assembly, but now I am stuck. I do not want to break the housing (that is all I need), so a link or
|