| Thread | Last Post | Replies |
|
| 2000 POLO ENGINE MANAGEMENT WOE! | 11 Jul 2007 15:58 GMT | 4 |
My 2000 reg Polo 1 litre is giving me loads of grief with warning lights. It started some time ago with the EPC light coming on and although I had it re-set a couple of times it kept coming back. I then got the valve changed (don't ask me which cos I'm not technical) and it kept ...
|
| Clogging sunroof drain lines | 11 Jul 2007 14:15 GMT | 22 |
My VW dealer just charged me 115.00 dollars to clean out the sun roof drain lines on my 02 gti. Front and rear passenger foot wells were flooded after a heavy rain. They told me it was a maintenance item. I can not find the maintenance procedure listed anywhere in the VW ...
|
| "Idle adaptation at limit" replace throttle body? | 11 Jul 2007 09:02 GMT | 3 |
I have a Mk4 Golf with the 2.0 motor (from Germany, not Mexico). For most of the car's life I've seen an intermittent check engine light that techs (at the dealer and indy) saw is from a faulty throttle body. As I recall, the code is P1582, "Idle adaptation at limit"
|
| '90 Vanagon: Where is the computer located? | 10 Jul 2007 22:32 GMT | 3 |
Hello to all: I have a 1990 Vanagon with idle problems. Sometimes perfectly stable at 1000rpm but mostly seems to just about stall out and often does... especially when humid or damp. Running on the road it is fine. Perfectly
|
| blower not working, 1998 passat UK | 10 Jul 2007 22:12 GMT | 9 |
It has climate control, ac system is working (pipe gets cold) but fan does not blow. Climate panel flashes at startup. Any clues? Is this something I can use a VagCom for? Where's the connector? Many thanks
|
| Difference in model numbers | 10 Jul 2007 04:55 GMT | 2 |
Okay so I know that a Jetta III is the 3rd version of the car. But I have a question I have been looking for tuning and upgrade parts online and a lot of the time it will ask which model they will have a Jetta MK III is that the same as Jetta III or is the European model
|
| Passat, 2007 Tire Pressure | 10 Jul 2007 04:52 GMT | 7 |
Does anyone know what the setpoint is for the "Tire Pressure Too Low" alarm in the new Passat. The dealer could not tell me. Thanks in advance
|
| Slipping Clutch | 10 Jul 2007 02:59 GMT | 2 |
Over the winter I removed my engine out of my 61 beetle for cosmetic reasons. Upon removal I noticed the throw out bearing was a bit was, it was worn in the center, the hole was kind of ovalled.. I decided while I had the engine out I would replace it.
|
| 95 Jetta III weirdness | 09 Jul 2007 19:33 GMT | 7 |
Okay so I have been noticing something weird I don't know if anyone else has had this issue or not. So it seems whenever my Jetta gets right around 1/2 empty it will start acting up on me. It is considerably noticeable when it is really hot outside. So what will
|
| Center muffler on Jetta III has a big hole in it .. The replacment muffler is 100 bucks | 08 Jul 2007 07:11 GMT | 2 |
Dynomax cat back is around 225 dollars..... Any advise ? How noisy is the Dynomax inside the car? What are the chances of having a clean installation of the center muffler?
|
| wiring a VW mk2 golf | 08 Jul 2007 06:34 GMT | 4 |
I just bought a 1985 golf. The guy who i bought it from, swaped the mk2 dash for a mk3, he left the original mk2 cluster in it. My problem is he either did not hook up the signals or he hooked them up wrong. Also the break lights keep blowing fuses. The running lights
|
| driveshaft and CV joint | 07 Jul 2007 21:45 GMT | 1 |
I replaced the driveshaft and CV joint on my rabbit today and I noticed some evidence of some poor quality work that was done in the past. The previous owner did not replace the small flywheel cover (I can see the flywheel thrugh a 1.5 inch or so opening. Also, the
|
| Propane tank for a Westy | 06 Jul 2007 22:27 GMT | 4 |
Hi all, I generally lurk here and not post much, but I am in need of a good propane tank for my 82 Westy. Since shipping these things is expensive (and potentially illegal!), I am looking for one, say within 100 miles of the Dallas/Ft. Worth, Texas area. If you have one, please ...
|
| VW valve job/tool | 06 Jul 2007 14:29 GMT | 1 |
Any recommendation on a tool that I should use to get out bent intake valves from a VW 2L 16V taken out from 91 passat with broken T-belt? Anything else that I would have to replace there except of the 4 bent intake valves (guides, seats etc?) Do I need to machine new valves
|
| Need guidance | 06 Jul 2007 14:26 GMT | 2 |
Ok did't get much response to the question about my 81 volkswagon convertable rabbit's fuel mixing with the oil. Is the engine toast because of it and were should i start. Someone told me oxygen sensor, I don't know alot about vw engines and because of being female i don't
|